Is it possible to set up an ipsec site-to-site VPN between a Cisco ASA (5510) and a Windows 2003 Server? (using RRAS or similar on the windows server) And the followup question - if this is possible, can anyone point me to a resource with details of the settings needed?

Apr 19, 2018 · Windows Server 2003 IPSec tunneling is not supported for client remote access VPN use because the Internet Engineering Task Force (IETF) IPSec Requests for Comments (RFCs) do not currently provide a remote access solution in the Internet Key Exchange (IKE) protocol for client-to-gateway connections. Before installing Windows 10 TP, I had two VPN Connections setup to my work locations. As far as I know, the settings for the VPN connections were identical. The Windows 10 TP installation deleted one of them (the later of the two). The one that was left continues to work fine, but the one that was deleted cannot be recreated. The vpn tunnel is between 2 subnets, x.x.0.x at the remote end and x.x.10.x at the SBS end. Each end of the VPN can ping the other by, but by IP only. The SBS firewall is turned off (which I'd like to remedy soon!!!) SBS Premium but ISA is not installed. What's missing in order to enable the remote end to be able to ping the server by name? Hi, I'm having trouble getting users with Windows 10 to connect to a Windows 2003 DC using VPN. I have tried on a few different Windows 10 computers so I know it is isolated to that OS. I can successfully connect using Windows 7 or XP computers.

protocol q | server 2003 file log | network mep unlock code | collaborative environment virtual | v7 network | phone client | configurazione di un access point | virtual memory tweaks | vpn 5 minutes

The routing between sites is set up as part of the site to site VPN configuration. Each RRAS router has a subnet route to the other site's subnet through the tunnel. The data is encrypted and encapsulated before it is sent out through the RRAS server's "public" NIC with a header using a "public" IP, namely the IP address of the target VPN server. Jul 26, 2005 · Note that there are a lot of different ways to "dial in to" a Windows Server 2003 system; a VPN is but one method. Other methods include wireless networks, 802.1x, and dial-up. Apr 28, 2006 · Just found your site and was searching for directions to setup a site-to-site vpn using windows 2003. I am not sure if you still monitor this post but I am also a IT Consultant. Been in the industry for 10 years but only recently done consulting. Its been a challenge but a worthwhile endeavor. Mar 01, 2009 · Re: SITE-To-SITE VPN using Windows Server 2003 Standard Its quite surprising to read that SITE-To-SITE VPN will work only when both SITES are using RFC1918 addresses, that is, private ip addresses.

A site-to-site VPN allows offices in multiple fixed locations to establish secure connections with each other over a public network such as the internet. Site-to-site VPN extends the company's network, making computer resources from one location available to employees at other locations.

In most cases, a site-to-site VPN would be the only service set up on a single network card and the firewall would be controlled by an external firewall in front of the server. But Microsoft does provide a way to configure Windows Server 2003 to allow VPN and other web services on the same card. the HQ has network 192.168.10.0 and Branch has network 192.168.11.0 and we have Win server 2003 and ISA 2004 on HQ site and traffic going to 192.168.11.0 from HQ is routed to ASA by the default gateway (Win 2k3 SBS) and both networks are configured as local on Server, but even after eliminating server and isa by making ASA the default gateway RE: How to setup Site-to-site VPN with SBS 2003 R2 Premium ShackDaddy (MIS) 20 Dec 08 17:08 The key to all clients being able to see each other is having everyone in both subnets register with a WINS server on one of the subnets. Forum discussion: Hi Look for some input on vpn and server network layout I what I wound like to Site one wound be 2003 r2 server with 5 client plus the dcu winch are unit that capture data from